Television media stand from vintage sideboard (part 3)

tvstand_before_after_pin.jpg

DSC_1683

DSC_1679

Wow! This project went a lot faster and was easier then I expected although we did have a few bumps in the road. Not sure why I waited so long!

tvstand_front_drawers_before

First, the vintage cabinet got some repairs and changes made to its structure. The inside shelf was removed, the height was shortened by removing two drawers, and veneer was replaced or repaired.

TIP – if looking to do the same find furniture that is made from 100% wood and is preferably with construction that is tongue and groove (hint: look at the drawers and inside corners).

Second, the television cabinet former sideboard was painted with two coats of Black Onyx semi gloss latex premium paint from Glidden. My other blog post has a lot of tips on how to use the HomeRight Paint Sprayer to make it go much easier and faster. However, I would not use this paint brand again (see below on why).

Now for the finishing touches:

First, we used a coat of paint stripper on the top of the cabinet. This was to remove any old topcoat of varnish or poly as well as clean off any gunk.

Next it was sanded using mostly a fine sandpaper on an electric sander. Again this was just to lighten the wood from the original stain. Husband did this for me and was very industrious! He got it down to bare wood and almost all of the damage out, except for one round stain that remains.

DSC_1674

The stain I used on the top is a water based, wood stain by General Finishes called Antique Oak. I like this color because it has a gray undertone in it and not the dreaded yellow or red color you see in other oak stains.

You may be more familiar with the wipe on Java gel stain this company offers due to the many, many Pinterest projects that use it 😀 If you haven’t used General Finishes before, I highly recommend their products. Very easy to use and a great result.

This water based, stain product is a bit thick like their Java Gel stain, and it is also grainy which surprised me. It went on darker then I expected but that was okay. It dried very fast! So work quickly! I used a foam brush applicator, wore latex gloves and wiped off with a lint clean rag.

TIP: This top was down to bare wood and it was very dry. It soaked up the stain very quickly so be aware you might need to work faster on old wood, vintage pieces then you would on projects that use new wood.

DSC_1677

After one coat of stain, I put on two protective coats of Velvet Finishes Protect on the top and Howard paste wax in neutral on the bottom. The first time using this wax and I’m impressed. Went on very easy (unlike Annie Sloan’s wax) and had the most delicious smell! Easy to buff too.

Behind the Scenes: I tried VF Protect on the black paint area and boy was that a mistake! It immediately started stripping off the paint! Whoa! So if using this product on anything but their own line do a test patch first. I already knew it worked well over this stain due to the kitchen island project where I used them both in combination.

The cabinet originally had wood knobs which I felt made it too country and dated for me. Those I replaced.

The doors didn’t close right and that wasn’t because they were warped (very hard to fix) but because they needed new hardware. Replaced!

Thoughts on this project:

I made a few mistakes. First one, is that I should have treated the bare wood panel we used on one side with a primer or sealant. Once the paint hit it, it raised the wood grain, giving a rough appearance to the surface. Solution? I gave it a slight hand sanding to smooth it down and then repainted that panel with the black.

Second mistake, when I put the cabinet up on 5 gallon buckets that wasn’t really high enough. I should have waited and used the sawhorses which would have allowed me to approach each side at a different angle by simply adding a step stool or not using a step stool. When you can’t change the paint approach slightly (instead you approach head on so to speak) it is hard to get coverage into crevices. I later touched that up with a foam brush.

Third mistake, I used the Velvet Finishes Protect on the black area without doing a test and disaster! It removed the black paint like a paint remover! Egad! Immediately cleaned it off with denatured alcohol, let dry and reapplied the black with a foam brush on the damaged areas.

I do wish I had sprayed on a primer. I think it would have given more grip for the paint and when I do the next project, the King Poster Bed, I will use a primer.

I also wish we had put some sort of ornamentation on the front kickboard area as it looks a little too plain next to all the other carving. OTOH, I’ve since swept in this room and the kickboard allowed me to get a clean sweep across without shoving dust under the unit. Yay!

I think this project would have looked even cooler in a color! Like a red, coral, turquoise or blue. However, I know we’ll be moving in a few years and wanted this in a classic color that would work with a lot of different furniture colors so black it was.

Future thoughts…

The inside of this unit is to store dvds but the current containers I have for them isn’t quite the right size. I looked at Target, Walmart, and Bed and Bath and no one has containers for DVDs??!!

I need a bin that has a straight side, not tapered (that removes the interior space) and with a lid. I found these small and large box at the Container Store so that looks like the storage solution there. Though still looking through various possibilities at Ikea.